1. Installation method of electric rolling shutter door:

 

，在需要安裝的門框框口位置畫線，表明尺寸的大小。注意：框內高度比門扇的高度要高一點點。

 

First of all, draw a line at the opening of the door frame to indicate the size. Note: the height inside the frame is a little higher than that of the door leaf.

 

其次，把電動卷簾門的門框固定，但是洞口兩側地面要記得預留凹槽。

 

Secondly, fix the door frame of the electric rolling shutter door, but remember to reserve grooves on the ground on both sides of the opening.

 

然后，安裝電動卷簾門扇主體門扇。安裝時，一定要保證電動卷簾門與墻體結成整體，而且封閉性要做好，再將洞口及墻體粉刷，確保美觀度。粉刷完后，應對門試試開啟關閉是否順暢自如。

 

Then, install the main door leaf of the electric rolling shutter door leaf. When installing, we must ensure that the electric rolling shutter door and the wall form a whole, and the sealing should be done well, and then the hole and the wall should be painted to ensure the beauty. After painting, try to open and close the door smoothly.

 

2、防火卷簾門安裝方法：

 

2. Installation method of fire shutter door:

 

a、按門的型號，量測產品各部位基本尺寸，檢查門的洞口是否與卷簾門尺寸相符，導軌和支架的預埋位置、數量是否正確。然后，測量洞口標高，彈出兩導軌垂線及卷筒中心線。

 

a. According to the door model, measure the basic size of each part of the product, check whether the door opening is consistent with the size of the rolling shutter door, and whether the embedded position and quantity of the guide rail and bracket are correct. Then, measure the elevation of the hole, pop up the vertical line of the two guide rails and the center line of the drum.

 

b、將墊板電焊在預埋鐵板上，用螺絲固定卷筒支架，安裝卷筒。卷筒的安裝應轉動靈活。

 

b. Weld the base plate on the embedded iron plate, fix the drum bracket with screws and install the drum. The installation of the drum should be flexible.

 

c、安裝減速器、傳動系統、裳電氣拴街系統。

 

c. Install reducer, transmission system and electrical tie down system.

 

d、將事先裝配好的簾板安裝在卷筒上。緊接著安裝導軌，按照圖紙規定的位置，將兩側及上方導軌焊牢于墻體預埋件上，并焊成以體，各導軌應在同一垂直平面上。

 

d. Install the pre assembled curtain board on the drum. Next, install the guide rail. According to the position specified in the drawing, weld the guide rail on both sides and above to the embedded parts of the wall, and weld them into a body. Each guide rail shall be on the same vertical plane.

 

e、安裝水幕噴淋系統，并與總控制系統連接。裝好后進行試運行，用電動機對門啟閉數次，調整無卡住、阻滯及異常的狀態即可。

 

5.jpg

 

e. Finally, the water curtain spray system is installed and connected with the main control system. After the installation, carry out trial operation, use the motor to open and close the door several times, and adjust it to the state without jamming, blocking and abnormality.

 

3、自動門水晶卷簾門安裝方法

 

3. Automatic door crystal shutter door installation method

 

，將電機固定在主板上，把鏈條固定在輪盤和電機底座齒輪連接，試下手柄是否顛倒，如果顛倒，遙控接收盒側方有黑色按鍵，向另一方撥動助即可。

 

First of all, fix the motor on the main board, fix the chain on the wheel disc and connect the gear of the motor base, and test whether the handle is reversed. If it is reversed, there is a black button on the side of the remote control receiving box, and you can just move the help to the other side.

 

其次，用尺子量主板和副板的外邊看下尺寸是否正確，如果正確把軸上在側板上，注意要打成一條水平線;再用10個鉆頭打孔50公分，每一個都要直;然后，用14的鏍母焊在軸上，記住一定要焊牢固;再把簾子的片的中心與軸上的孔對齊，并用快絲固定就可。

 

Secondly, measure the outside of the main board and the auxiliary board with a ruler to see if the size is correct. If the shaft is on the side board correctly, make a horizontal line. Then, drill 50 cm with 10 drills, and each one should be straight. Then, weld the shaft with 14 screws, and remember to weld it firmly. Then, align the center of the first piece of the curtain with the hole on the shaft, and fix it with a quick screw.

 

再次，將卷簾門的簾片穿好，兩側用封頭封好。封完后，用繩翻過軸把簾子打孔用繩拴住，再把簾子升上去，切忌一定要牢固。

 

Thirdly, put on the curtain piece of the rolling shutter door and seal both sides with heads. After sealing, use the rope to turn over the shaft to punch holes in the curtain, use the rope to tie it, and then lift the curtain up. Be sure not to be firm.