1、 How to open the electric rolling shutter door without electricity?

1、停電時門開著的,去拉電機上的一條鏈子,費一點時間就可以關上門。但是人就會被關在室內。

1. When the power is off, the door is open. Go and pull a chain on the motor. It takes a little time to close the door. But people will be locked in.

2、停電時門關著的,人又在室內,去拉電機上的一條鏈子,費一點時間就可以打開門。

2. When the power is off, the door is closed, and the person is in the room. Go to pull a chain on the motor, and it takes a little time to open the door.

3、停電時門關著的,人又在室外,只有等到來電才。 在進行卷簾門安裝的時候,可以安裝不間斷的電源比如后備電源,這樣遇到停電時就不用擔心了。

3. When the power is off, the door is closed, and the person is outside. It can only be solved when the power is on. When installing the rolling shutter door, you can install uninterruptible power supply, such as backup power supply, so that you don't have to worry about power failure.
            

二、電動卷簾門怎么安裝？

2、 How to install the electric rolling shutter door?

1、經校正合格后。表明尺寸大小,然后找工作人員設計出合適的電動卷簾門。用水泥砂漿或強度不低于10MPa細石混凝土嵌塞牢固即可。注意,這里值得注意的一點是框內高度比門扇的高度要一點點。一定要保證電動卷簾門與墻體結成整體,固定木楔。

1. After the correction, it is qualified. Show the size, and then find the staff to design a suitable electric roller shutter door. Cement mortar or fine aggregate concrete with strength not less than 10MPa can be used to firmly plug. Notice that the height inside the frame is a little higher than that of the door leaf. We must ensure that the electric shutter door and the wall form a whole, fixed wedge.

2、先在需要安裝的門框框口位置畫出線,門縫應均勻平整、先把電動卷簾門的門框固定,不得有過緊。

2. First, draw the outlet line at the door frame opening to be installed, and the door seam shall be even and flat. First, fix the door frame of the electric rolling shutter door without over tightening.

3、洞口兩側地面要預留凹槽,再粉刷洞口及墻體,這里要先拆掉門框下部的固定板。

3. Groove should be reserved on both sides of the hole, and then the hole and wall should be painted. Here, the fixed plate at the lower part of the door frame should be removed first.

4、封閉性要做好,開啟電動卷簾門應該自由輕便,門框鐵腳與預埋鐵板件焊牢。粉刷完畢后、安裝電動卷簾門扇主體門扇一、過松和反彈現象。

4. The sealing should be done well, the opening of the electric rolling shutter door should be free and light, and the iron foot of the door frame and the embedded iron plate should be welded firmly. After finishing painting, install the main door leaf of electric rolling shutter. First, the door leaf is too loose and rebounds.

感謝您的閱讀，希望以上內容對您有所幫助，如您想了解更多精彩內容請點擊我們的官網：濟南電動卷簾門安裝維修//domachine.com.cn。

Thank you for reading, I hope the above content is helpful to you, if you want to know more wonderful content, please click our official website: Jinan electric roller shutter door installation and maintenance //domachine.com.cn .