Electric roller shutter door often appears in daily life, for example, garage, shops will choose electric roller shutter door, which is not only very safe but also very convenient. Today, I'd like to introduce the common problems and installation steps of the electric rolling shutter door in detail.

電動卷簾門沒電怎么辦?

How to do without electricity for electric rolling shutter door?

1、停電時門開著的,去拉電機上的一條鏈子,費一點時間就可以關上門。但是人就會被關在室內。

1. When the power is off, the door is open. Go and pull a chain on the motor. It takes a little time to close the door. But people will be locked in.

2、停電時門關著的,人又在室內,去拉電機上的一條鏈子,費一點時間就可以打開門。

2. When the power is off, the door is closed, and the person is in the room. Go to pull a chain on the motor, and it takes a little time to open the door.

3、停電時門關著的,人又在室外,只有等到來電才。在進行卷簾門安裝的時候,可以安裝不間斷的電源比如后備電源,這樣遇到停電時就不用擔心了。

3. When the power is off, the door is closed, and the person is outside. It can only be solved when the power is on. When installing the rolling shutter door, you can install uninterruptible power supply, such as backup power supply, so that you don't have to worry about power failure.
                              

電動卷簾門安裝步驟：

Installation steps of electric rolling shutter door:

1、先在需要安裝的門框框口位置畫出線。表明尺寸大小，然后找工作人員設計出合適的電動卷簾門，這里值得注意的一點是框內高度比門扇的高度要高一點點。

1. First, draw the outgoing line at the position of the door frame to be installed. Show the size, and then find the staff to design a suitable electric roller shutter door. It is worth noting that the height of the frame is a little higher than that of the door leaf.

2、先把電動卷簾門的門框固定，這里要先拆掉門框下部的固定板。(注意：洞口兩側地面要預留凹槽，經校正合格后，固定木楔，門框鐵腳與預埋鐵板件焊牢。用水泥砂漿或強度不低于10MPa細石混凝土嵌塞牢固即可。)

2. First, fix the frame of the electric rolling shutter door. Here, first remove the fixing plate at the lower part of the frame（ Note: grooves shall be reserved on the ground at both sides of the hole. After the correction is qualified, the wooden wedge shall be fixed, and the iron foot of the door frame shall be firmly welded with the embedded iron plate. Cement mortar or fine aggregate concrete with strength not less than 10MPa can be used to firmly plug.)

3、安裝電動卷簾門扇主體門扇。一定要保證電動卷簾門與墻體結成整體，封閉性要做好，再粉刷洞口及墻體。粉刷完畢后，門縫應均勻平整，開啟電動卷簾門應該自由輕便，不得有過緊、過松和反彈現象。

3. Install the main door leaf of electric rolling shutter door leaf. We must ensure that the electric rolling shutter door and the wall form a whole, the sealing should be done well, and then paint the hole and the wall. After painting, the door seam should be even and smooth, and the opening of the electric roller shutter door should be free and light, without too tight, too loose and rebound phenomenon.

感謝您的閱讀，希望以上內容能對您有所幫助，如您想了解更多精彩內容請點擊我們的官網：濟南電動卷簾門安裝維修//domachine.com.cn。

Thank you for reading, I hope the above content can help you, if you want to know more wonderful content, please click our official website: Jinan electric roller shutter door installation and maintenance //domachine.com.cn .