底邊在各種快速門和工業門中非常常見，其保護功能極強，尤其是近兩年用戶青睞的快速門，底邊也是其標準配置之一。安裝后，為了保證其功能的正常使用，需要進行相關的功能測試，以保證其在保護用戶方面發揮應有的作用。

The safety bottom edge is very common in all kinds of fast doors and industrial doors, and its safety protection function is very strong, especially the fast door most favored by users in recent two years. The safety bottom edge is also one of its standard configurations. After installation, in order to ensure the normal use of its functions, relevant functional tests need to be carried out to ensure that it plays its due role in protecting users.

安裝快速門底邊時，先將底邊盒連接線接到電氣柜端子上，按標準編號連接。注意：當電控柜內沒有GND終端點時，將通訊線連接到g點，這樣當門落地后碰到壓力管底邊時，就會收到信號。當COM線接在X5時，落地后碰到壓力管底邊，所以收不到信號。

When installing the safety bottom edge of the fast door, first connect the connecting wire of the bottom edge box to the terminal of the electrical cabinet and connect it according to the standard number. Note: when there is no GND terminal point in the electric control cabinet, connect the communication line to point G, so that when the door touches the bottom edge of the pressure pipe after landing, it will receive the signal. When the com line is connected to X5, it touches the bottom edge of the pressure pipe after landing, so the signal cannot be received.

安裝調試后，需要對其功能進行測試，快速門分析具體測試步驟如下：

After installation and commissioning, its function needs to be tested. The specific test steps of fast door analysis are as follows:

關閉緊急停止按鈕并打開電源。按下底部接收器面板上的學習按鈕一次，信號接收器亮起。

Turn off the emergency stop button and turn on the power. Press the learning button on the bottom receiver panel once and the signal receiver lights up.

按壓底部布口袋中的壓力軟管數次，信號接收器指示燈閃爍，成功接收記憶。反復按下底部壓力軟管，每次信號連接完成時，接收器燈亮一次。

Press the pressure hose in the bottom cloth pocket several times, the signal receiver indicator flashes, and the memory is successfully received. Press the bottom pressure hose repeatedly, and the receiver light comes on once each time the signal connection is completed.

打開電氣柜的急停按鈕，按下底部布口袋中的壓力軟管。當哈爾濱快速門收到信號后，會自動上升，正常運行。

Open the emergency stop button of the electrical cabinet and press the pressure hose in the bottom cloth pocket. When Harbin express door receives the signal, it will rise automatically and operate normally.

在測試和使用底邊的過程中，如果發現電控柜接收不到底邊信號，需要檢查底邊變送器和底邊壓力軟管中的電池，看電池是否耗盡，如果耗盡，更換新的。檢查底部壓力軟管是否損壞或泄漏。如果損壞或泄漏，將其密封。如有必要，用新的底部壓力軟管更換。

In the process of testing and using the safety bottom, if it is found that the electric control cabinet cannot receive the safety bottom signal, it is necessary to check the battery in the safety bottom transmitter and bottom pressure hose to see if the battery is exhausted. If it is exhausted, replace it with a new one. Check the bottom pressure hose for damage or leakage. If damaged or leaking, seal it. If necessary, replace with a new safety bottom pressure hose.