電動卷簾門是一種性能優越的快速升降隔離門，電動卷簾門可以在化工、、電子廠、物流倉儲等行業看到，該卷簾門的外觀一般由高強度冷板噴塑完成，這對于電動卷簾門安裝后的調試和驗收尤為重要。下面來說說電動卷簾門底邊的驗收測試。

The electric rolling shutter door is a kind of fast lifting isolation door with superior performance. The electric rolling shutter door can be seen in the chemical industry, supermarket, electronics factory, logistics and storage industries. The appearance of the rolling shutter door is generally completed by high-strength cold plate spraying, which is particularly important for the commissioning and acceptance of the electric rolling shutter door after installation. Let's talk about the acceptance test of the safety bottom edge of the electric roller shutter door.

1、先關閉電動卷簾門急停按鈕，打開電動卷簾門電控箱電源，按一下底部接收面板的學習按鈕，檢查指示燈是否亮信號接收器打開。

1. First close the emergency stop button of the electric roller shutter door, turn on the power supply of the electric cabinet of the electric roller shutter door, press the learning button on the bottom receiving panel, and check whether the indicator light is on and the signal receiver is on.

2.按下電動卷簾門底邊的壓力軟管數次，信號指示燈閃爍表示接收成功。反復按壓底邊壓膠管，每次接收燈亮，測試信號連接是否完成。

2. press the pressure hose at the safety bottom of the electric roller shutter door for several times, and the signal indicator flashes to indicate that the reception is successful. Press the bottom edge pressure hose repeatedly, and each time the receiving light is on, test whether the signal connection is completed.

3、打開電動卷簾門電控箱急停按鈕，按下底部側布袋中的壓力軟管，電動卷簾門門體收到信號后自動上升，門體將正常運行。

3. Open the emergency stop button of the electric control box of the electric roller shutter door, press the pressure hose in the bottom side cloth bag, the electric roller shutter door body will rise automatically after receiving the signal, and the door body will operate normally.

4、然后在檢測電動卷簾門底邊和使用電動卷簾門的過程中，如果發現電控箱接收不到底邊信號，需要注意檢查電池在底邊變送器和底邊壓力軟管中。如果發現電池電量耗盡，請更換新電池。如果底邊壓力軟管損壞和泄漏，應將損壞和泄漏的空氣密封，必要時更換新的底邊壓力軟管。

4. Then, in the process of detecting the safety bottom edge of the electric roller shutter door and using the electric roller shutter door, if it is found that the electric control box cannot receive the safety bottom edge signal, it is necessary to check that the battery is in the safety bottom edge transmitter and the bottom edge pressure hose. If the battery is found to be discharged, replace it with a new one. If the bottom pressure hose is damaged or leaking, seal the damaged or leaking air, and replace it with a new safety bottom pressure hose if necessary.

此外濟南電動卷簾門安裝維修廠家認為相應的保養注意事項要明確，比如：

In addition, the Jinan electric roller shutter door installation and maintenance manufacturer believes that the corresponding maintenance precautions should be clear, such as:

1、只能根據現行零件清單使用原廠供應商配件，用來保障更換的配件可以正常使用，如更換使用的配件不為原廠配件可能導致電動卷簾門出現其它問題或引發事故；

1. The original supplier's accessories can only be used according to the current parts list to ensure that the replaced accessories can be used normally. If the replaced accessories are not original accessories, other problems or accidents may occur to the electric roller shutter door;

2、更換制動線圈時，電動卷簾門制動控制裝置要一起更換；

2. When replacing the brake coil, the brake control device of the electric roller shutter door shall be replaced together;

3、電動卷簾門電機在工作過程中溫度可能會變得非常高，所以在保養電動卷簾門時應在暫停一段時間后在對電機進行保養，以免有燙傷的危險；

3. The temperature of the motor of the electric roller shutter door may become very high during operation, so the motor should be maintained after a period of suspension to avoid the risk of scalding;

4、緊固或者降低升降機驅動裝置需更具注意，以免有墜落的危險；

4. Pay more attention to fastening or lowering the drive device of the lift to avoid the risk of falling;

5、在開始維護電機和制動器之前，要先切斷電源，并且采取措施防止意外發生。

5. Before starting to maintain the motor and brake, cut off the power supply and take measures to prevent accidents.

以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注我們網站//domachine.com.cn并咨詢我們的工作人員，將竭誠為您服務。

The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website //domachine.com.cn And consult our staff, will serve you wholeheartedly.