電動卷簾門一般調試都是由安裝師傅來調試的，如果是自己家里進行調試，要怎么去做呢？下面濟南電動卷簾門安裝維修人員為您講解講解相關內容。

The electric rolling shutter door is generally debugged by the installation master. If it is debugged at home, how do you do it? Now, the installation and maintenance personnel of Jinan electric rolling shutter door will explain the relevant contents for you.

先要看控制面板上的func按鍵，可以按住這個鍵，長按8秒鐘，卷簾門就開始進行開關門進程和過載力設置過程。然后再按inc鍵，按住不放以后，電機就開始運行，這個時候電機是將門向上打開的進程，到了合適的位置，然后停止INC鍵，再按住STA鍵，就能夠設置好打開的卷簾門程序。然后再按住DEC鍵，那么決定了就開始向下關閉，到達一定位置以后再按sta鍵，就可以設置好關門的進程。

First, look at the func key on the control panel. You can press and hold this key for 8 seconds to start the process of opening and closing the shutter door and the process of overload force setting. Then press the inc key again. After holding it down, the motor starts to run. At this time, the motor is the process of opening the door upward. When it reaches the appropriate position, stop the INC key, and then press the STA key to set the open rolling shutter door program. Then press and hold the DEC key, and the door will be closed down after the decision is made. After reaching a certain position, press the sta key to set the process of closing the door.

在電動卷簾門的使用過程中，要盡量保持控制器和電壓的穩定，禁止安裝在非常潮濕的環境，另外不要隨意打開遙控器，如若發現門體上有電線纏繞、打結等應及時處理。注意通道的是否堵塞，阻礙門體下降，如若發生異響應立即停止電機運作。

During the use of the electric rolling shutter door, the controller and voltage shall be kept stable as much as possible. It is prohibited to install it in a very humid environment. In addition, the remote controller shall not be opened at will. In case of any wire winding or knotting on the door, it shall be handled in a timely manner. Pay attention to whether the passage is blocked to prevent the door body from descending, and stop the motor immediately in case of abnormal response.

要經常性的檢查電動卷簾門上下行程的開關，對行程控制器加上潤滑油，保持正常良好的運行，另外，操作人員手動控卷簾門，檢查器運行情況，校對上下行程開關位置，使電動卷簾門開啟或關閉時處于適當位置，且檢查過程中嚴防電動卷簾門沖頂或沖底或者反轉，如若出現緊急情況應立即停止轉動，切斷電源。

Frequently check the up and down travel switch of the electric roller shutter door, add lubricating oil to the travel controller, and maintain normal and good operation. In addition, the operator manually controls the roller shutter door, checks the operation of the device, and checks the position of the up and down travel switch, so that the electric roller shutter door is in the proper position when it is opened or closed. In addition, the electric roller shutter door is strictly prevented from rushing to the top or bottom or reversing during the inspection process. In case of an emergency, the rotation should be stopped immediately, Cut off the power.

操作員經常性的要檢查好電動卷簾門的手動開關和手動升降裝飾，以防止在緊急的情況下電動卷簾門會失靈，或者造成不必要的事故。關注我們//domachine.com.cn，帶您了解更為詳細的信息！

The operator shall regularly check the manual switch and manual lifting decoration of the electric roller shutter door to prevent the electric roller shutter door from failing or causing unnecessary safety accidents in an emergency. Follow us //domachine.com.cn , to guide you to more detailed information!