Step 1: prepare the installation tool. Operators shall prepare electric welding machine, electric hammer, electric hand drill, ladder, drill bit, cutting head, level gauge, screwdriver and other tools and accessories.

第二步：確定電動卷簾門安裝尺寸大小。作業人員在門框的位置畫出線條，確定好電動卷簾門的大小，然后，讓施工人員定做出合適尺寸的電動卷簾門，通常，電動卷簾門的高度要略高于門框。

Step 2: determine the installation size of the electric rolling shutter door. The operator shall draw lines at the position of the door frame to determine the size of the electric rolling shutter door, and then let the construction personnel determine the electric rolling shutter door of appropriate size. Generally, the height of the electric rolling shutter door shall be slightly higher than the door frame.

電動卷簾門怎么安裝 電動卷簾門

How to install electric rolling shutter door price of electric rolling shutter door

第三步：確定水平線，根據現場情況來設定尺寸。作業人員在卷簾門側板的洞口上方50厘米處，使用水平尺畫出一條水平線;然后，在卷簾門的側板跨出洞口13厘米處，使用水平尺畫下一條垂直線;再把副板跨出門框的9厘米處，畫出一條垂直線;將側板固定在垂直線上，將側板的處畫上一條水平線。

Step 3: determine the horizontal line and set the size according to the site conditions. The operator shall draw a horizontal line 50 cm above the opening of the side plate of the rolling shutter door with a level ruler; Then, draw a vertical line with a horizontal ruler at the place where the side plate of the rolling shutter door crosses 13 cm out of the hole; Then cross the auxiliary plate 9 cm out of the door frame and draw a vertical line; Fix the side plate on the vertical line and draw a horizontal line on the highest part of the side plate.

第四步：作業人員將電機固定在主板上，再使用鏈條將輪盤和電機底座連接，把遙控線盒裝置和電機相連接，測試卷簾門的手柄是否顛倒，如果電動卷簾門的遙控接收盒顛倒，則需要撥動內置的黑色按鍵。

Step 4: the operator fixes the motor on the main board, then uses the chain to connect the wheel disc with the motor base, connects the remote control wire box device with the motor, and tests whether the handle of the rolling shutter door is reversed. If the remote control receiving box of the electric rolling shutter door is reversed, it is necessary to dial the built-in black button.

第五步：電動卷簾門焊接牢固。電動卷簾門確定尺寸合適之后，將其與轉軸焊接牢固，讓焊接的鉆頭打孔保持垂直。作業人員檢查電動卷簾門的電源工作是否正常，將卷簾門的軌道拉成人字，將卷簾門調成水平，確定上下水平線位置準確，再使用螺絲桿將簾子升上去。

Step 5: the electric rolling shutter door shall be firmly welded. After the size of the electric rolling shutter door is determined to be appropriate, it shall be firmly welded with the rotating shaft to keep the drilling of the welded drill vertical. The operator shall check whether the power supply of the electric rolling shutter door works normally, pull the track of the rolling shutter door into a word, adjust the rolling shutter door to be horizontal, determine the accurate position of the upper and lower horizontal lines, and then use the screw rod to raise the curtain.

第六步：檢查與測試。作業人員打開電源之后，拉動電動卷簾門的開關，進行升降演示操作，確保其不會出現失靈等情況，從而造成事故的發生。作業人員確定電動卷簾門的軌道通暢、潔凈，按鈕不會出現反彈失靈等問題。

Step 6: Inspection and test. After the operator turns on the power supply, pull the switch of the electric rolling shutter door to carry out the lifting demonstration operation to ensure that it will not fail, resulting in safety accidents. The operator shall ensure that the track of the electric rolling shutter door is smooth and clean, and the button will not rebound or fail.

以上的精彩內容來自： 濟南電動卷簾門安裝維修提供分享，更多的精彩內容請點擊進入我們的網站：//domachine.com.cn，我們會有更多的精彩內容等您查看

The above highlights come from: Jinan electric rolling shutter door installation and maintenance to share. For more highlights, please click to enter our website: //domachine.com.cn , we will have more wonderful content for you to see