在門的使用過程中，總會不可避免地出現一些這樣或那樣的小故障影響著門的運行，這時找電動卷簾門廠家來處理，時間上來不及，因此掌握一些必要應急處理措施十分重要。下面濟南電動卷簾門安裝維修人員為您講解相關措施方法吧。

During the use of the door, some small faults of one kind or another will inevitably occur, which will affect the operation of the door. At this time, the manufacturer of electric rolling shutter door will be asked to deal with it. It is too late, so it is very important to master some necessary emergency treatment measures. Now the installation and maintenance personnel of Jinan electric roller shutter door will explain the relevant measures and methods for you.

誤按下電動卷簾門的緊急停止按鈕，導致門體既不能升又不能降，遇到這一情況時，該如何處理呢？其實很簡單，再次按下急停按鈕，將其旋轉復位，電動卷簾門即可恢復正常的上升、下降運行。

The emergency stop button of the electric roller shutter door is pressed by mistake, which results in the door body can neither be raised nor lowered. What should be done in this case? In fact, it is very simple. Press the emergency stop button again, rotate it to reset, and the electric roller shutter can resume normal ascending and descending operation.

在門向下關閉運行時，紅外線出現了偏離，這時紅外線的遇阻反彈功能必將大受影響，通行人員、車輛的將無法保障。

When the door is closed downward, the infrared safety line deviates. At this time, the rebound function of the infrared safety line will be greatly affected, and the safety of pedestrians and vehicles will not be guaranteed.

大家都知道，紅外對射裝置大多安裝在高速門的軌道下端，如果紅外線 出現偏離，須立即調整兩側紅外探頭的方向，使其對射，兩側的紅外光束連成一條直線，這樣才不會出現偏離。

As we all know, most of the infrared aiming devices are installed at the lower end of the high-speed door track. If the infrared ray deviates, the direction of the infrared probes on both sides must be adjusted immediately to make them aim and the infrared beams on both sides connect in a straight line, so that the deviation will not occur.

如果在使用過程中，發現高速門出現限位不準或失靈情況，怎么辦呢？不要著急，冷靜下來，仔細檢查門編碼器的端頭部分，看其是否出現脫落，有的話，需要在編碼器的端頭添加上一塊墊片，這樣端頭與編碼器之間就不會再出現脫落了。

What if the high-speed door is found to have inaccurate limit or failure during use? Don't worry. Calm down and carefully check the end of the door encoder to see if it falls off. If so, add a gasket to the end of the encoder, so that the end will not fall off from the encoder again.

當電動卷簾門使用中出現這樣或那樣的小故障時，大家不要急，一定要冷靜下，慢慢分析、檢查可能發生問題的原因，一一排除，若實在處理不了，立即聯系廠家技術人員，要求其派人上門處理。更多相關事項就來我們網站//domachine.com.cn咨詢吧！

When this or that kind of small fault occurs in the use of the electric roller shutter door, everyone should not be anxious. We must calm down, slowly analyze and check the causes of the possible problems, and eliminate them one by one. If it is really impossible to solve it, immediately contact the manufacturer's technical personnel, and ask them to send someone to handle it. Come to our website for more information //domachine.com.cn Consult!