隨著經濟的發展，卷簾門的應用領域愈加廣泛，已經不斷應用到大型、、地下車庫、廠房及其他人員密集的場所，在使用過程中難免會遇到一些小問題需要，在此廠家總結幾點常見故障及處理方法供大家參考。

With the development of economy, the application field of roller shutter door is more and more extensive, and it has been continuously applied to large supermarkets, shopping malls, underground garages, workshops and other densely populated places. It is inevitable to encounter some small problems to be solved in the process of use. Here, the manufacturer summarizes some common faults and treatment methods for your reference.

一、卷簾門不動：應檢查電源，看卷簾門的電源空開是否有電，如果沒電，就應線檢查電源部分。如果有電，此時卷簾控制箱的電源指示燈應當是綠色常亮。如果指示燈不亮此時我們應檢查控制箱內的變壓器（變壓器的電阻270歐姆)是否燒壞。如果電源指示燈是綠色閃爍，表明電源部分可能缺相，如果電源不缺相有可能是控制箱的備用電源板燒壞；也有可能住電源板和備用電源板都燒壞。

1、 The rolling shutter door does not move: check the power supply to see whether the power supply of the rolling shutter door is powered. If there is no power, check the power supply part. If there is electricity, the power indicator of the roller shutter control box should be green and always on. If the indicator light is not on, we should check whether the transformer in the control box (the resistance of the transformer is 270 ohms) is burnt out. If the power indicator is flashing green, it indicates that the phase of the power supply may be missing. If the phase of the power supply is not missing, the standby power board of the control box may be burned out; It is also possible that both the live power board and the standby power board are burnt out.

二、電源空開推不上：送閘時，空開推不上應檢查備用板是否有問題，備用板的輸出線的電阻約為300歐姆。如果開路時或短路應該檢查電機的點剎車是否燒壞，或檢查備用板是否燒壞。

2、 The power supply air switch cannot be pushed: when the switch is sent, if the air switch cannot be pushed, check whether there is a problem with the spare board. The resistance of the output line of the spare board is about 300 ohms. In case of open circuit or short circuit, check whether the point brake of the motor is burnt out, or check whether the spare board is burnt out.

三、操作按鈕使用不靈：應當先按下停止鍵，再按下復位鍵，然后按上行下行鍵。

3、 The operation button does not work well: you should first press the stop key, then press the reset key, and then press the up and down keys.

四、電源控制箱或按鈕面板的指示燈全亮：這時應先檢查按鈕線是否有短路現象或某一個按鈕被壓死的可能，如果以上現象不存在，有可能是電源主板上的芯片壞掉，這時應更換芯片。注意要反著裝，（即開口對著開口）。

4、 The indicator lights of the power control box or button panel are all on: at this time, check whether there is a short circuit in the button line or whether a button may be crushed to death. If the above phenomenon does not exist, it may be that the chip on the power motherboard is broken, and the chip should be replaced at this time. Pay attention to reverse dressing (i.e. opening to opening).

五：卷簾門按鈕操作只有上行或下行：這時應先檢查限位線是否有掉線現象，如果沒有，有可能是主電源板壞了。

5： The operation of the roller shutter door button is only up or down: at this time, check whether the limit line falls off. If not, it may be that the main power board is broken.

六、卷簾門操作按鈕不好用或按什么按鈕都是下行，應先檢查主電板與備電板的連接排線時是否松動

6、 If the operation button of the rolling shutter door is not easy to use or any button is pressed, it is necessary to check whether the connecting cable between the main board and the standby board is loose

七、增加鎖控：只需在排線的第5和12的空上串接一個約1K的電阻。

7、 Add lock control: just connect a resistance of about 1K in series on the air of the 5th and 12th of the flat line.

八、判斷電機的好壞：電機的三相電阻達47-70歐姆且三相平衡。三相不平衡可能是電機壞了。

8、 Judge whether the motor is good or bad: the three-phase resistance of the motor is 47-70 ohms and the three-phase is balanced. The three-phase imbalance may be caused by the motor failure.

九、卷簾門報警時，應當先讓卷簾門自動下降到底，途中不要按任何按鈕，然后再上行。

9、 When the rolling shutter door gives an alarm, the rolling shutter door should be automatically lowered to the bottom first, and then it should not press any button on the way, and then it will go up.

十、卷簾門的安裝調試：濟南電動卷簾門安裝維修人員認為在安裝調試之前應先檢查控制器、按鈕盒、卷門機、行程開關、電剎車的連接線是否正常，確認后在進行調試。

10、 Installation and commissioning of rolling shutter door: the installation and maintenance personnel of Jinan electric rolling shutter door believe that before installation and commissioning, they should first check whether the connecting wires of controller, button box, door rolling machine, travel switch and electric brake are normal, and then conduct commissioning after confirmation.

以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注我們網站//domachine.com.cn并咨詢我們的工作人員，將竭誠為您服務。

The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website //domachine.com.cn And consult our staff, will serve you wholeheartedly.