電動車庫門，企業常用設施，適用于商業門面、車庫、、醫院、廠礦企業等公共場所或住宅。尤其是門洞較大，不便安裝地面門體的地方起到方便、快捷開啟作用。電動車庫門安裝需注意這五點，下面濟南車庫門安裝維修廠家為您講解。

Electric garage door, a common facility for enterprises, is suitable for commercial storefronts, garages, shopping malls, hospitals, factories and mining enterprises and other public places or residences. Especially where the door opening is large and it is inconvenient to install the door body on the ground, it can play a convenient and quick opening role. The installation of electric garage door needs to pay attention to these five points. Next, Jinan garage door installation and maintenance manufacturer will explain to you.

1、電動車庫門須按說明書要求安裝。其實不僅僅是卷閘門的電機需要按照說明書進行安裝，對于門的安裝事項也需要嚴格按照說明書進行，這樣才能保證安裝后能夠正常使用。

1. The electric garage door must be installed according to the instructions. In fact, not only the motor of the rolling gate needs to be installed according to the instructions, but also the installation of the door needs to be carried out strictly according to the instructions, so as to ensure the normal use after installation.

2、確定安裝水平線及垂直線，按設定尺寸依次安裝。槽口尺寸應準確，上下保持一致，對應槽口應在同一平面內，然后用連接件與洞口內的預埋件焊牢。

2. Determine the installation horizontal line and vertical line, and install them according to the set size. The notch size shall be accurate and consistent from top to bottom. The corresponding notch shall be in the same plane, and then the connector shall be welded with the embedded part in the hole.

3、卷軸、文架板須牢固地裝在混凝土結構上或預埋件上。寬大門體需在中間位置加裝中柱，兩邊有滑道，中柱安裝須與地面垂直，安裝牢固，但要拆裝方便。

3. The reel and document shelf plate must be firmly installed on the concrete structure or embedded parts. The wide door body needs to be installed with a central pillar in the middle, with a slide on both sides. The central pillar must be installed vertically with the ground and firmly, but it should be easy to disassemble.

4、安裝完略，先手動調，自試運行，觀察門體上下運行情況，正常后通電調試。觀察卷簾機、傳動系統、門體運行情況應啟閉正常、順暢，速度為3-7米/分鐘。如果出現問題那么調整制動器外殼方向，使環形鏈朝下，調整鏈條張緊度，鏈條6-10mm，調整單向調節器及限位器，就可以使用了。

4. After the installation is completed, manually adjust it first, conduct self-test, observe the up and down operation of the door body, and then conduct power-on commissioning after it is normal. Observe the operation of the roller shutter, transmission system and door body. The opening and closing shall be normal and smooth, and the speed shall be 3-7 m/min. If there is a problem, adjust the direction of the brake housing so that the annular chain is downward, adjust the chain tension, 6-10mm, adjust the one-way adjuster and limiter, and then it can be used safely.

5、卷筒安裝應先找好尺寸，并使卷簡軸保持水平位置。注意與導軌之間的距離應兩端保將一致，臨時固定后進行檢查，并進行要的調篷、校正，無誤后再與支架預埋件用電焊焊接。后就是清理、粉刷或鑲砌導軌墻體裝飾面層，清理現場。

5. When installing the drum, first find the size and keep the winding shaft in a horizontal position. Note that the distance between the guide rail and the guide rail should be the same at both ends. After temporary fixing, check it, adjust and correct it, and then weld it with the embedded parts of the support by electric welding. After that, clean, paint or inlay the decorative surface of the guide rail wall, and clean the site.

綜上所述，我們對于安裝車庫門時應該注意的事項有了比較深入的了解，您對此還有什么問題就來我們網站//domachine.com.cn進行咨詢了解吧！

To sum up, we have a deeper understanding of the matters that should be paid attention to when installing the garage door. If you have any questions about this, please come to our website //domachine.com.cn Consult and understand!