Electric rolling shutter door is often used in our life. How to adjust the limiter of Jinan electric rolling shutter door has been perplexing many customers. Let's introduce the adjustment method of roller shutter door limiter.

濟南電動卷簾門

Jinan electric rolling shutter door

電動卷簾門一般有兩個限位開關。一個是上限，另一個是下限。限位開關應具械旋轉桿，以控制開關的端部和打開。調整時，應由兩人操作。一人可以調整頂部機械旋轉桿的位置，另一人可以控制電動卷簾門的上下位置，配合限位開關位置的調整。

The electric rolling shutter door generally has two limit switches. One is the upper limit and the other is the lower limit. Limit switches shall be equipped with mechanical rotating rods to control the end and opening of the switch. When adjusting, it should be operated by two people. One person can adjust the position of the top mechanical rotating rod, and the other person can control the up and down position of the electric rolling shutter door to cooperate with the adjustment of the position of the limit switch.

電動卷簾門限調試方法：

Commissioning method of electric rolling shutter threshold:

1.將止動塊上的螺母卡箍轉動到適當的方向，以分離螺母塞，或松開止動塊上的夾緊螺釘。

1. Turn the nut clamp on the stop block to the appropriate direction to separate the nut plug or loosen the clamping screw on the stop block.

2.打開車門正確位置，轉動限位器上的限位螺母，按下車門開啟限位開關上的滾輪。聽到“咔嗒”聲后，將螺母卡入相應的限位螺母或擰緊螺釘。

2. Open the door to the correct position, turn the limit nut on the limiter, and press the roller on the door opening limit switch. After hearing the "click", clip the nut into the corresponding limit nut or tighten the screw.

3.將車門關閉到適當位置，轉動限位器上的限位螺母，并按下關閉限位開關上的滾輪。聽到“咔嗒”聲后，將螺母卡入相應槽中的限位螺母或擰緊螺釘。

3. Close the door to the proper position, turn the limit nut on the limiter and press the roller on the closing limit switch. After hearing the "click", clip the nut into the limit nut in the corresponding slot or tighten the screw.

4.如果門的位置不合適，可以將其再次調整到合適的位置。

4. If the position of the door is not appropriate, it can be adjusted to the appropriate position again.

電動卷簾門的設置要求：

Setting requirements for electric rolling shutter door:

1.當吊鉤滑動到限位置時，提升操縱桿。當按下限位開關時，電源關閉，只有在箱子關閉時才能降下吊鉤。

1. When the hook slides to the limit position, lift the control lever. When the limit switch is pressed, the power is turned off, and the hook can be lowered only when the box is closed.

2.在軌道邊緣安裝固定限位擋板(在控制裝置限制的位置)。當塔式起重機運行到此位置時，限位擋板接觸行程開關手柄并斷開電源以控制行程。重合閘時，塔機只能反向運行。

2. Install a fixed limit baffle at the edge of the track (at the position limited by the control device). When the tower crane runs to this position, the limit baffle contacts the travel switch handle and disconnects the power supply to control the travel. During reclosing, the tower crane can only operate in reverse.

3.在光盤中安裝一個垂直移動的指針。當振幅改變時，指針指示各種振幅下的額定起重能力。當臂桿移動到上、下限位時，分別按住限位開關，斷開控制電路，變幅電機停止，實現限位功能。

3. Install a vertically moving pointer in the disc. When the amplitude changes, the pointer indicates the rated lifting capacity at various amplitudes. When the arm moves to the upper and lower limits, press and hold the limit switch respectively, disconnect the control circuit, and the luffing motor stops to realize the limit function.

本文由濟南電動卷簾門安裝維修為您提供，我們的網站是：//domachine.com.cn我們將以全心全意的熱情為您提供服務，歡迎您的訪問

This article is provided for you by Jinan electric rolling shutter door installation and maintenance. Our website is: //domachine.com.cn We will serve you with wholehearted enthusiasm. Welcome to visit