1. Recheck whether the hole size is consistent with the product size. The hole size of fireproof rolling shutter door can be determined according to 3m.

2、確定安裝水平線及垂直線，按設定尺寸依次安裝.槽口尺寸應準確，上 下保持一致，對應槽口應在同一平面內，然后用連接件與洞口內的預埋件焊牢。

2. Determine the installation horizontal line and vertical line, and install them in sequence according to the set size. The notch size shall be accurate, consistent up and down, and the corresponding notch shall be in the same plane, and then weld the connector with the embedded parts in the hole.

3、卷門機必須按說明書要求安裝。

3. The door rolling machine must be installed according to the instructions.

4、卷軸、文架板必須牢固地裝在混凝土結構上或預埋件上。

4. The reel and document frame plate must be firmly installed on the concrete structure or embedded parts.

5、寬大門體需在中間位置加裝中柱，兩邊有滑道.中柱安裝必須與地面垂 直，安裝牢固,但要拆裝方便。

5. The wide door body needs to be equipped with a center column in the middle, with slides on both sides. The center column must be installed perpendicular to the ground, firmly installed, but easy to disassemble.

6、門體葉片插入滑道不得少于30 mm，門體寬度偏差為土3 mm。

6. The insertion of the gate blade into the slide shall not be less than 30 mm, and the width deviation of the gate body shall be 3 mm.

7、防火卷簾門水幕系統裝在防護理下面,噴嘴傾斜15°角。

7. The water curtain system of fireproof rolling shutter door is installed under the anti-corrosion protection, and the nozzle is inclined at an angle of 15 °.

8、安裝完略,先手動調'自試運行，觀察門體上下運行情況，正常后通電調試。

8. After installation, manually adjust the "self commissioning" first, observe the up and down operation of the door body, and then power on for commissioning after it is normal.

9、觀察卷簾機、傳動系統、門體運行情況應啟閉正常、順暢,速度為3-7 米/分鐘。

9. Observe the operation of the rolling shutter machine, transmission system and door body. The opening and closing shall be normal and smooth, and the speed shall be 3-7M / min.

10、調整制動器外殼方向，使環形鏈朝下;調整鏈條張緊度，鏈條6-10 mm;調整單向調節器及限位器。

10. Adjust the direction of the brake housing so that the annular chain faces down; Adjust the chain tension, 6-10 mm; Adjust the one-way regulator and limiter.

11、卷筒安裝應先找好尺寸，并使卷簡軸保持水平位置。注意與導軌之間的距離應兩端保將一致，臨時固定后進行檢查,并進行必要的調篷、校正,無誤后再與支架預埋件用電焊焊接。

11. When installing the drum, first find the size and keep the winding shaft horizontal. Note that the distance between the guide rail and the guide rail shall be consistent at both ends. After temporary fixing, it shall be checked, and necessary adjustment and correction shall be carried out. After it is correct, it shall be welded with the embedded parts of the support by electric welding.

12、清理、粉刷或鑲砌導軌墻體裝飾面層，清理現場。

12. Clean, paint or inlay the decorative surface of guide rail wall, and clean the site.